Hayward salt cell: life expectancy, care and repair

Is your salt system showing low salt, the Check Salt and Inspect Cell lights, or is the chlorine staying low? When the salt shown is far from the real level, about 95% of the time the cell is at the end of its life, not the board. Here’s how long a cell lasts, how to test it, and how to make the next one last.

Applies to: Aqua Rite, Aqua Trol, Swim Pure, Aqua Nature, Pro Logic, Aqua Logic, Aqua Rite PRO, OmniLogic and OmniPL with a Hayward T-CELL-3, 5, 9 or 15.

How long does a salt cell last?

According to the manufacturer’s specification, an original Hayward cell lasts about 10,000 hours of production. What matters is not its age but how many hours it has made chlorine. And you decide that number of hours: the percentage and the pump hours control the life of your cell.

The percentage (the middle dial) sets the share of the pump run time during which the cell produces. At 50% with the pump running 24 hours a day, the cell produces 12 hours a day; at 20%, only 4 h 48. The system only produces while the pump runs.

Examples for a June to September season, pump running 24 hours a day:

SettingHours per dayHours per seasonCell life
20%4 h 48584 hover 10 years
40%9 h 361,167 habout 8.6 years
60%14 h 241,751 habout 5.7 years
100%24 h2,918 habout 3.4 years

These estimates are based on the manufacturer’s specification (10,000 hours). Water chemistry can also shorten a cell’s life: see Make your cell last longer.

Most people set the percentage far too high: the liner fades and the cell doesn’t last. It’s rarely more than 30%, except for a very large pool. Example: 26,000 gallons (100,000 L), T-15 cell, pump 24 h a day: about 20% in peak summer and 15% the rest of the season, even less with a solar cover. If your pool runs all year, the cell wears out three times faster than in a June to September season.

Calculate your cell’s life

Enter your cell, your percentage, your pump hours and how many months the pool is open: the calculator shows the chlorine produced and the estimated life of your cell.

Don’t go by the purchase date: check the serial number on the sticker. On an original Hayward cell, it starts with 1E or 3E followed by the year (3E21 = 2021), and the first digit is the warranty in years. It’s often older than you think. Generic cells vary a lot in lifespan from one supplier to another.

Can a salt cell be repaired? Not by us

We repair Hayward electronic boards, not cells: we don’t test, repair or sell salt cells. For a worn cell, contact Pool Cell Repair (Saint-Jean-sur-Richelieu, Quebec): they replace the plates for a fraction of the price of a new cell.

Before you buy a cell or have one repaired, make sure it really is the cell: in rare cases, the board reads it wrong.

Cell or board? How to test your salt cell

  1. Have your water tested at a pool store. Without a real test, there is nothing to compare. A gap of a few hundred ppm (up to 500) with the system is normal.
  2. Check that the system is set for your cell (T-CELL-3, 5, 9 or 15, on the sticker). If it’s set wrong, it always shows a wrong salt level.
  3. Do the instant salt test (Aqua Rite): switch to OFF then back to AUTO, then press Diagnostic 5 times. The 5th value, starting with a minus sign, is the salt the cell reads right now.
  4. Still far from the store test: it’s almost always the cell. To be sure, send us a photo of both sides of the main board.

The bucket test proves nothing. Even if you put the cell in a bucket of water and see bubbles, it doesn’t mean the cell works correctly. A worn cell still makes bubbles, just fewer than when new, and that’s very hard to see.

The board’s age matters too. In our experience, we only see boards fail after about 10 years in Canada, where the system runs about half the year, and after about 5 years in warm climates where it runs all year. If your board is younger, it’s even more likely to be the cell.

Check Salt and Inspect Cell lights on together: not enough salt, or a cell at the end of its life. Inspect Cell flashing alone: it’s not a fault, just a 500-hour reminder.

Make your cell last longer

The percentage decides how long the cell lasts, but water chemistry matters too:

  • Set the percentage by testing the chlorine in the morning (the sun destroys some during the day): aim for about 1 ppm. Change it a little at a time.
  • Keep the pH at 7.4: at pH 8 it takes 3 times more chlorine, and people raise the percentage for nothing.
  • Stabilizer protects the chlorine from the sun and lets you lower the percentage. Too much makes the chlorine less effective: have your water tested.
  • Before adding salt or chemicals, set the system to OFF (or 0%). Adding chemicals while the system runs wears the cell and the board faster.
  • Inspect Cell light: inspect the cell and clean it only if there is scale. Never scrape the plates: acid cleaning when it isn’t needed shortens its life.
  • When you close the pool for the winter, store the cell indoors: water freezing inside can damage it.

Does your board need a repair?

The test points to the board, or the Power light is off? We repair original Hayward boards within 1 to 2 business days after we receive them, with a 1-year warranty.

Questions? Call us at 438 448-0782.

See also